PORSCHE 356 B SUSPENSION REARCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1994-98 - Uncategorized (includes uncategorized and accessory items) 115900996BIT02 The pss 10 suspension kit provides the ultimate in performance tuning. The fully adjustable monotube gas shock absorbers offer a selection of nine precise compression and rebound settings. The front and rear progressive rate springs allow accurate adjustment of the vehicle ride height and center of gravity for the level of performance you seek. Handling and control are just a few twists away.
$4,802.60
Make a selection 115900997TTCS The ultimate bilstein sport suspension for club racing and street performance! This suspension was developed under real racing conditions by bilstein with double world rally champion walter rohrl. - reduced weight via the use of an integrated reservoir. - 2 way damping adjustment (bound (red) and rebound (blue) independently). - dials with good visibility and scaling (from 1 to 10). - easy to adjust when installed with click screening and color coding. - bilstein mono-tube gas pressure technology. - adjustable aluminum uniball camber plates (rear). - TUV approved. - made in Germany. What's in the box: - adjustable dampers including double springs. - rear uniball camber plates. - spring tensioning key (tool). -...(choose a part on the right to read more)
$7,256.70
Make a selection 150PB100915 Replace worn-out original sway bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber, so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. We also recommend replacing the sway bar to ball pin bushing at the same time to save on labor costs, part # 90134378200 sold individually. 4 necessary per car. Please note: this fit's genuine rear sway bars only.
$44.00
Make a selection FVD33399602B6 Bilstein suspension featuring eibach springs. Lowering 35 mm front and 30 mm rear - giving it a GT3 stance
$1,930.50
Make a selection 1588501000 Originally published by floyd clymer this is a faithful reproduction of the 1967 publication of that manual. Includes complete technical data, service and maintenance information and comprehensive detailed instructions for the repair and overhaul of all major and minor mechanical and electrical components. Covers the Porsche 356-356a-356b-356c series from 1948 through 1965, making it an invaluable resource for collectors and restorers of these classic automobiles. There are separate sections that deal with the repair and overhaul procedures for the engine, ignition system, fuel system, clutch, transmission, rear suspension, steering, front suspension, brakes, shocks, heater and exhaust plus a detailed electrica...(choose a part on the right to read more) General FitmentACCESSORY
$45.50
Make a selection 150PB100919 Replace worn-out original sway bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber, so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. We also recommend replacing the sway bar to ball pin bushing at the same time to save on labor costs, part # 90134378200 sold individually. 4 necessary per car. Please note: this fit's genuine rear sway bars only.
$44.00
Make a selection 150PB100916 Replace worn-out original sway bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber, so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. We also recommend replacing the sway bar to ball pin bushing at the same time to save on labor costs, part # 90134378200 sold individually. 4 necessary per car. Please note: this fit's genuine rear sway bars only.
$44.00
Make a selection FVD33150030 This kit is complete and includes a total of 8, 4 smaller and 4 larger for the rear control arms. Our weather sealed monoball cartridges are crafted in high carbon steel and 7075 t6 aircraft aluminum. They will positively locate the suspension arms so suspension motion is accurately repeated in every corner. Sold as a set of 8. 1 kit is necessary per car. Please note: noise may resonate inside the cabin during street use.
$746.90
Make a selection BBI9914010006 The bbi street cup suspension package improves the handling response of the vehicle by upgrading the factory springs with an improved linear rate springs and replacing the factory arms and links with the motorsport cup version that uses spherical bearings.
$7,295.00
Make a selection FVD33150040R Replace worn-out original rear sub frame (side panel) bushings with our FVD clubsport series. They are made of rubber with an 85 shore hardness value, that is the same as the rennsport models. 85 shore is more durable, provides more positive suspension location and is still quiet and comfortable for street use. This bushing is made in Germany. It is crafted in high carbon steel and 7075 t6 aircraft aluminum and includes an 85 shore hardness value core. This is a front and rear bushing for one sub frame. 2 are necessary per car. We also sell the entire right and left rear sub frames with these bushings already installed, please order our part # FVD331993001.
$429.00
Make a selection FVD33300909ATK This non-adjustable rear spring plate is remanufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. New rs spec. (85 shore) rubber bushings are installed to make this a direct bolt on. 85 shore rubber is more durable than OEM 65 shore and provides more positive suspension location yet is still quiet and compliant for street use. Features: includes new rs spec. (85 shore) rubber bushings made in Germany sold individually. 2 necessary per car. This part is a remanufactured part. Send us your original and we will have it remanufactured for you. We do not offer a core exchange on this part. Each is remanufactured in Germany, so the lead times can vary.
$342.10
Make a selection FVD33150003 Rear toe control arms - order in pairs only restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm can't compensate enough when lowering your Porsche, leaving you stuck with as much as ½ of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration.
$218.90
Make a selection BK7033 Re-issue of autobooks manual covering engine, fuel & cooling systems, ignition, heating, exhaust emissions, clutch, transmission, rear axle, suspension, steering gear, brakes, electronics, and bodywork. This is a manual that will help keep 912 on the road. A must for any 912 owner. General FitmentACCESSORY
$32.00
Make a selection FVD33398701 Bilstein suspension featuring with upside/down technology. Lowering 35 mm front and 30 mm rear - giving it a GT3 stance.
$2,803.90
Make a selection FVD33399600B6 Bilstein suspension featuring with upside/down technology. Lowering 35 mm front and 30 mm rear - giving it a GT3 stance
$2,442.00
Make a selection FVD33399600B8 Bilstein suspension featuring with upside/down technology. Lowering 35 mm front and 30 mm rear - giving it a GT3 stance
$2,310.00
Make a selection FVD33399300 A cost effective FVD exclusive combination of bilstein clubsport shocks with a set of TUV certified eibach springs. This suspension kit will lower the front axle to a maximum of 35 mm (1.37 inches) and the rear axle to 30 mm (1.18 inches), like the European rennsport model. The height is adjustable as the dampers are threaded. They are a cost effective solution for clubsport use and will be well mannered on the street. Sold as a complete kit. 1 kit is necessary per car.
$11,872.30
Make a selection FVD33300905 This rear spring plate is manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. New rs spec. (85 shore) rubber bushings are installed to make this a direct bolt on. 85 shore rubber is more durable than OEM 65 shore and provides more positive suspension location yet is still quiet and compliant for street use. Features: made from ¼ inch spring steel includes new rs spec. (85 shore) rubber bushings made in Germany sold individually. 2 necessary per car.
$273.90
Make a selection FVD341999R Replace worn-out original soft rubber (65 shore hardness value) control arm bushings with our FVD clubsport series. They are made from rubber with a 85 shore hardness value which is the same as the rennsport models. 85 shore is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This is the ideal upgrade for street and light track / clubsport use. This bushing set is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes 85 shore hardness value cores. This is a front and rear bushing for the front lower control arm (wishbone). 2 sets are necessary per car.
$124.30
Make a selection 11599702 Non pasm cars - lowers the front 1.0 inch (25 mm) and the rear 1.0 inch (25 mm). Pasm cars - lowers the front .8 inches (20 mm) and the rear .8 inches (20 mm). Targa - lowers the front 1.3 inches (35 mm) and the rear 1.3 inches (35 mm).
$470.80
Make a selection 115974 (2) model 928: parts of the suspension must be changed depending on manufacture date.
$517.00
Make a selection 150SPB976 Replace worn-out spring plate bushings with these longer lasting poly-graphite plastic bushings. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. This includes the inner and outer bushing for the 2-piece adjustable spring plate. Sold individually. 2 necessary per car.
$39.60
Make a selection 150SPB965 Replace the worn-out spring plate bushing with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. This is the inner bushing for the 1-piece non-adjustable spring plate. Sold individually. 2 necessary per car.
$47.30
Make a selection 115910996034 Bilstein b4 OEM m030 (original m030 suspension) shock absorber set (4 pieces) for cars with lowering springs or cars delivered with factory m030 sport suspension. Nothing is better than the original! The b4 m030 dampers from bilstein are the perfect shock absorber for lowered cars. Facts: - constant damping pressure under load - increased driving stability - increased durability - OEM quality - bilstein gas pressure technology - type/model m030
$1,784.11
Make a selection FVD33391101SET These bushings are manufactured from higher density, rs specification rubber (85 shore). Rs bushings are more durable than OEM 65 shore, provide more positive suspension location and are still quiet and compliant for street use. This set is a direct replacement for original part # 911 333 009 00 sold as a set. 1 necessary per axle.
$108.90
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |